fit tolerance
英 [fɪt ˈtɒlərəns]
美 [fɪt ˈtɑːlərəns]
配合公差
双语例句
- How does this reading of Indian history fit with your thesis that powers achieve predominance through tolerance and pluralism?
这些对印度历史的看法，是否符合你关于大国通过宽容和多元化获得优势的理论呢？ - Construction of four to see: a good quality paint in strict accordance with the requirements that the ratio should feel fine, shiny uniform, uniform color, viscosity fit, good construction tolerance.
四看施工性：质量优良的油漆严格按说明要求配比后，应手感细腻、光泽均匀、色彩统一、黏度适宜，具有良好的施工宽容度。 - The Effect of Integral Key Fit Clearance beyond the Tolerance of Rolling Mill Screw-down Motor on Service Performance of Rolling Mill Influences of Porosity Error on Electrical Properties of Rock and Updating Formula as Well as Correction Charts
轧机压下丝杆花键配合间隙超差对轧机使用性能影响的分析孔隙度误差对岩电参数的影响及校正公式和图版 - Introduces a practical aided design expert system for fit tolerance, and its retrieval mechanism used Case-Based Reasoning ( CBR) to improve the efficiency and accuracy of the query.
将基于案例推理（CBR）和专家系统理论应用到故障诊断领域，对雷达装备的故障诊断问题进行研究，形成一个集成的智能诊断专家系统。 - An aided design expert system for fit tolerance using case-based reasoning
应用案例推理的配合公差辅助设计专家系统 - The contact compressive stress on the mating surface increases with the increase of interference fit tolerance or tube thickness;
配合面内的接触压应力随过盈配合量或柱筒厚度的增加而增大； - The effects of fit tolerance, coefficient of friction, the wall thickness of shaft sleeve, rotational speed and the contact stress distribution on the mating surfaces were discussed in the numerical computation.
针对不同的过盈量、摩擦因数、轴套壁厚和转速进行计算，获得了叶轮、轴套与轴之间接触应力的分布规律。 - The relation between the outer diameter of free upsetting blank and the inner diameter of cold extrusion die can be comprehended as clearance fit, to confirm the basic tolerance and tolerance band of the blank.
将自由镦粗毛坯外径与冷挤压凹模的关系理解为间隙配合，确定了毛坯的基本偏差和公差带。 - Based on the fit theory the slide fit tolerance clearances with various sizes and signs can be calculated in S_ ( min), S_ ( mar) and.
根据公差配合理论可以计算不同配合、不同公差尺寸的S（mia）、S（max）及ψ。 - This paper discusses the influence of fit tolerance selection on reliability of internal combustion engine.
本文从配合公差选用角度来探讨其对可靠性的影响。 - Discussion and Selection on Fit Tolerance of Oil Pump Parts
机油泵零件配合公差的探讨与选用 - In the sheet metal incremental forming, the orientation of bolster model positioned by guide pin is inefficient and rough because of the floating of bolster model and fit tolerance between guide pin and aligning hole.
在板料的无模渐进成形过程中，使用导正杆定位底支撑模型，由于配合误差和模型浮动等问题造成定位效率低、精度差。 - Based on the nonlinear FEA software ANSYS, two FEA simulated calculating methods were adopted in the autofrettage and fit tolerance assembling. Element birth-death method and heating-cooling method were proposed to solve the complicated nonlinear problems in the autofrettage and fit tolerance assembling.
基于非线性有限元软件ANSYS对液压联轴器的外套自紧、过盈装配过程进行了有限元的仿真计算，提出单元生死法和降温升温法解决外套自紧身及过盈装配过程复杂的非线性问题。 - Touch on replacement of shrink fit in tolerance system by inorganic bonding
论以无机粘接取代过盈配合 - The influence of thermal deformation on clearance fit and interference fit are discussed. A new tolerance design method that compensates thermal deformation is presented.
本文重点分析热变形对孔、轴类配合的影响，提出了通过修正公差设计补偿热变形误差的理论方法和具体措施，为全面提出热公差配合理论奠定了良好的基础； - A new calculating method for group assembly design through the use of distribution curves of fit dimensions 'errors and the graphics of their two-dimensional distribution zone and the extreme deviations of fit tolerance is presented in this paper.
本文利用配合尺寸误差的分布曲线、二维分布域和配合公差的极限偏差的图示，提出了分组装配设计的一种新的计算方法。 - Through using of degree of freedom and tolerance zone of a feature, Assembly model is established to present fit feature, component feature, assembly geometric relation, assembly dimension, assembly tolerance, and assembly datum, etc.
利用特征自由度和特征公差带，建立装配模型来表示装配设计中的配合特征、零件特征、装配几何关系、装配尺寸关系、装配公差关系以及装配基准参照系等。 - And results show that the time-interleaved signals fit for long distance transmission more better due to its high tolerance of nonlinear effects.
结果表明，时隙间插信号由于非线性容限高，更适合长距离传输。